Does this guide apply to your appliance?

Match the brand, device type and complete display code. The same code can mean something different on another product family or market; a series name does not confirm every model in that series.

Model and family references in this record:

Commercial GradeBravosBravos XLMaximaFront Load WasherTop Load Washer

Likely causes

  • Hot or cold water supply valves are turned off or partially closed
  • Inlet water supply hoses are kinked, pinched, or damaged
  • Sediment or mineral buildup clogging the water inlet valve filter screens
  • Anti-flood or flood-safe supply hoses restricting water flow rate
  • Low household water pressure
  • Failed internal water inlet valve assembly or pressure sensor switch

What to try

Inspect water supply valves and inlet hoses

Easy
  1. Press the Power button to cancel the error; if the washer initiates an automatic drain routine, wait 8 to 10 minutes for it to complete.
  2. Ensure both the hot and cold water shut-off valves behind the washer are fully turned on.
  3. Inspect the full length of both inlet hoses to verify there are no sharp bends, crimps, or kinks restricting water flow.
  4. Ensure standard supply hoses are used; if restrictive auto-shutoff or anti-flood hoses are installed, replace them with standard braided hoses.

Clean water inlet valve screens

Easy
  1. Unplug the washing machine from the electrical wall outlet.
  2. Turn off both the hot and cold water shut-off faucets completely.
  3. Unthread the inlet hoses from the connections at the back of the washer, keeping a bucket and towel ready to catch residual water.
  4. Inspect the small mesh filter screens inside the washer's water inlet valve ports for sediment, rust, or mineral scale.
  5. Carefully clean the screens with a soft-bristled brush to remove any trapped debris.
  6. Reattach the hoses to the correct hot and cold ports, tighten securely, turn the water taps back on fully, check for leaks, plug the appliance back in, and run a test cycle.

This step is marked caution. Stop if you are not qualified to continue.

Test household water pressure and isolate for technician

Moderate
  1. Turn off the water taps and disconnect the supply hoses from the washer.
  2. Direct the loose ends of both hoses into a deep bucket or utility sink and open each tap individually to verify steady, strong water pressure.
  3. If water pressure is low or erratic, contact a licensed plumber to inspect household plumbing lines.
  4. If household pressure is normal and hoses/screens are clean but F8 E1 returns, the internal solenoid valve or water level sensor is faulty; isolate the washer from power and water and contact a qualified technician.

This step is marked caution. Stop if you are not qualified to continue.

The code returned or the check did not help?

Avoid repeated resets and do not select a replacement part from the code alone. Record the exact code, full model number, when it appeared, and the checks you tried with their results. Share these details with the manufacturer or service technician.

Disconnecting power does not establish that internal components are safe to touch. This guide does not authorize opening electrical components or bypassing safety devices.

Related error codes

Maytag SdMaytag Washing Machine Error Code Sd: Excessive Suds Detected Maytag F5 E2Maytag Washing Machine Error Code F5 E2: Door or Lid Lock Failure Maytag F7 E1Maytag Washer F7 E1 Error Code: Motor Speed or Tachometer Signal Problem Maytag F8 E2Maytag Washing Machine Error Code F8 E2: Dispenser System Fault Maytag F9 E1Maytag Washing Machine Error Code F9 E1: Long Drain Samsung 1CSamsung washing machine error code 1C: water-level sensor or leakage issue

Useful guides

Washing Machine Will Not Drain: Safe Checks Before Booking a TechnicianA blocked filter, kinked hose, plumbing restriction, unbalanced load, or excess suds can stop a washer from dr... Why Your Washing Machine Shakes or Moves—and Safe Leveling ChecksShaking can come from an uneven load, shipping bolts left in place, or an unstable floor. Try these safe check... Too Much Foam in Your Washer: Safe Steps to TakeExcess suds can lengthen a cycle, interfere with spinning and leave laundry wet or poorly rinsed. Check your d...

References