Does this guide apply to your appliance?

Match the brand, device type and complete display code. The same code can mean something different on another product family or market; a series name does not confirm every model in that series.

Model and family references in this record:

Maytag Front Load WasherMaytag top-load washer

Likely causes

  • An overloaded or poorly distributed load is preventing the washer from reaching the expected motor speed.
  • Shipping bolts or plastic spacers were not removed from a recently installed front-load washer.
  • A missing or incorrect motor-speed or tachometer feedback signal, depending on the washer model.
  • A fault in the wiring, connectors, motor, actuator or sensor, or electronic control system; the exact component cannot be identified from F7 E1 alone.

What to try

Reduce or redistribute the load

Easy
  1. Stop the cycle and wait until the washer has safely stopped moving.
  2. Open the washer when the door or lid unlocks.
  3. Remove some items if the load is tightly packed, or redistribute the items evenly.
  4. Retry the cycle with a smaller, balanced load.
  5. If F7 E1 returns with an empty or balanced load, continue with the reset and service steps.

Source for this check: producthelp.maytag.com

Check shipping hardware on a recently installed front-load washer

Moderate
  1. Turn the washer off and disconnect its power before checking the rear exterior.
  2. Look at the back of the washer for the shipping bolts and plastic spacers used for transport.
  3. Confirm that all four shipping bolts and their plastic spacers were removed during installation.
  4. Do not operate the washer with shipping hardware installed; use the installation instructions for your exact model if hardware remains.
  5. Reconnect power and retry the cycle only after the installation issue has been corrected.

This step is marked caution. Stop if you are not qualified to continue.

Source for this check: producthelp.maytag.com

Reset the washer

Easy
  1. Cancel the cycle and leave the washer in a safe, stopped condition.
  2. Unplug the washer, or switch off its circuit breaker.
  3. Wait about five minutes.
  4. Restore power and run a short test cycle with a small, balanced load.
  5. If F7 E1 comes back, stop repeating resets and arrange model-specific service.

Source for this check: producthelp.maytag.com

Arrange professional diagnosis if the code persists

Professional

This is a service referral, not a do-it-yourself repair procedure.

  1. Record the complete model number and whether the washer is front-load or top-load.
  2. Note whether F7 E1 appears with an empty, balanced load and after the reset.
  3. Use the model number to obtain the correct Maytag manual and service information.
  4. Schedule a qualified appliance technician if the code returns or the washer cannot complete a cycle.
  5. Do not replace the motor, sensor, actuator, control, or other part based on the error code alone.

This step is marked professional. Stop if you are not qualified to continue.

Source for this check: producthelp.maytag.com

The code returned or the check did not help?

Avoid repeated resets and do not select a replacement part from the code alone. Record the exact code, full model number, when it appeared, and the checks you tried with their results. Share these details with the manufacturer or service technician.

Disconnecting power does not establish that internal components are safe to touch. This guide does not authorize opening electrical components or bypassing safety devices.

Related error codes

Maytag SdMaytag Washing Machine Error Code Sd: Excessive Suds Detected Maytag F5 E2Maytag Washing Machine Error Code F5 E2: Door or Lid Lock Failure Maytag F8 E1Maytag Washing Machine Error Code F8 E1: Water Fill or Flow Detection Fault Maytag F8 E2Maytag Washing Machine Error Code F8 E2: Dispenser System Fault Maytag F9 E1Maytag Washing Machine Error Code F9 E1: Long Drain Samsung 1CSamsung washing machine error code 1C: water-level sensor or leakage issue

Useful guides

Washing Machine Will Not Drain: Safe Checks Before Booking a TechnicianA blocked filter, kinked hose, plumbing restriction, unbalanced load, or excess suds can stop a washer from dr... Why Your Washing Machine Shakes or Moves—and Safe Leveling ChecksShaking can come from an uneven load, shipping bolts left in place, or an unstable floor. Try these safe check... Too Much Foam in Your Washer: Safe Steps to TakeExcess suds can lengthen a cycle, interfere with spinning and leave laundry wet or poorly rinsed. Check your d...

References